213 lines
8.6 KiB
C
213 lines
8.6 KiB
C
#ifndef __SPI_FLASH_H
|
||
#define __SPI_FLASH_H
|
||
|
||
#include "stm32h7xx.h"
|
||
#include <stdio.h>
|
||
|
||
/* Private typedef -----------------------------------------------------------*/
|
||
//#define sFLASH_ID 0xEF3015 //W25X16
|
||
//#define sFLASH_ID 0xEF4015 //W25Q16
|
||
//#define sFLASH_ID 0XEF4017 //W25Q64
|
||
//#define sFLASH_ID 0XEF4018 //W25Q128
|
||
#define sFLASH_ID 0XEF4019 //W25Q256
|
||
|
||
/* QSPI Error codes */
|
||
#define QSPI_OK ((uint8_t)0x00)
|
||
#define QSPI_ERROR ((uint8_t)0x01)
|
||
#define QSPI_BUSY ((uint8_t)0x02)
|
||
#define QSPI_NOT_SUPPORTED ((uint8_t)0x04)
|
||
#define QSPI_SUSPENDED ((uint8_t)0x08)
|
||
|
||
|
||
/* W25Q256JV Micron memory */
|
||
/* Size of the flash */
|
||
#define QSPI_FLASH_SIZE 24 /* 地址总线宽度访问整个内存空间 */
|
||
#define QSPI_PAGE_SIZE 256
|
||
|
||
/* QSPI Info */
|
||
typedef struct {
|
||
uint32_t FlashSize; /*!< 闪存大小 */
|
||
uint32_t EraseSectorSize; /*!< 擦除操作的扇区大小 */
|
||
uint32_t EraseSectorsNumber; /*!< 擦除操作的扇区数 */
|
||
uint32_t ProgPageSize; /*!< 编程操作的页面大小 */
|
||
uint32_t ProgPagesNumber; /*!< 编程操作的页面数 */
|
||
} QSPI_Info;
|
||
|
||
/* Private define ------------------------------------------------------------*/
|
||
/*命令定义-开头*******************************/
|
||
/**
|
||
* @brief W25Q256JV配置
|
||
*/
|
||
#if USE_DUAL_ExtFLASH
|
||
#define W25Q256JV_FLASH_SIZE 0x4000000 /* 512 MBits => 64MBytes */
|
||
#endif
|
||
#define W25Q256JV_FLASH_SIZE 0x2000000 /* 256 MBits => 32MBytes */
|
||
#define W25Q256JV_BLOCK_SIZE 0x10000
|
||
#define W25Q256JV_SECTOR_SIZE 0x1000 /* 256 sectors of 64KBytes */
|
||
//#define W25Q256JV_SUBSECTOR_SIZE 0x1000 /* 4096 subsectors of 4kBytes */
|
||
#define W25Q256JV_PAGE_SIZE 0x100 /* 65536 pages of 256 bytes */
|
||
|
||
#define W25Q256JV_DUMMY_CYCLES_READ 4
|
||
#define W25Q256JV_DUMMY_CYCLES_READ_QUAD 10
|
||
|
||
#define W25Q256JV_BULK_ERASE_MAX_TIME 250000
|
||
#define W25Q256JV_SECTOR_ERASE_MAX_TIME 3000
|
||
#define W25Q256JV_SUBSECTOR_ERASE_MAX_TIME 800
|
||
|
||
/**
|
||
* @brief W25Q256JV 指令
|
||
*/
|
||
/* 复位操作 */
|
||
#define RESET_ENABLE_CMD 0x66
|
||
#define RESET_MEMORY_CMD 0x99
|
||
|
||
#define ENTER_QPI_MODE_CMD 0x38
|
||
#define EXIT_QPI_MODE_CMD 0xFF
|
||
|
||
/* 识别操作 */
|
||
#define READ_ID_CMD 0x90
|
||
#define DUAL_READ_ID_CMD 0x92
|
||
#define QUAD_READ_ID_CMD 0x94
|
||
#define READ_JEDEC_ID_CMD 0x9F
|
||
|
||
/* 读操作 */
|
||
#define READ_CMD 0x03
|
||
#define READ_CMD_4BYTE 0x13
|
||
#define FAST_READ_CMD 0x0B
|
||
#define FAST_READ_CMD_4BYTE 0x0C
|
||
#define DUAL_OUT_FAST_READ_CMD 0x3B
|
||
#define DUAL_INOUT_FAST_READ_CMD 0xBB
|
||
#define QUAD_OUT_FAST_READ_CMD 0x6B
|
||
#define QUAD_INOUT_FAST_READ_CMD 0xEB
|
||
#define QUAD_INOUT_FAST_READ_CMD_4BYTE 0xEC
|
||
|
||
/* 写操作 */
|
||
#define WRITE_ENABLE_CMD 0x06
|
||
#define WRITE_DISABLE_CMD 0x04
|
||
|
||
/* 寄存器操作 */
|
||
#define READ_STATUS_REG1_CMD 0x05
|
||
#define READ_STATUS_REG2_CMD 0x35
|
||
#define READ_STATUS_REG3_CMD 0x15
|
||
|
||
#define WRITE_STATUS_REG1_CMD 0x01
|
||
#define WRITE_STATUS_REG2_CMD 0x31
|
||
#define WRITE_STATUS_REG3_CMD 0x11
|
||
|
||
|
||
/* 编程操作 */
|
||
#define PAGE_PROG_CMD 0x02
|
||
#define QUAD_INPUT_PAGE_PROG_CMD 0x32
|
||
#define Enter_4Byte_Addr_Mode_CMD 0xB7
|
||
#define QUAD_INPUT_PAGE_PROG_CMD_4BYTE 0x34
|
||
#define EXT_QUAD_IN_FAST_PROG_CMD_4BYTE 0x12
|
||
|
||
/* 擦除操作 */
|
||
#define SECTOR_ERASE_CMD 0x20 //0xD8擦：64K 0x52擦：32K 0x20擦：4K
|
||
#define SECTOR_ERASE_CMD_4BYTE 0x21
|
||
#define BLOCK32_ERASE_CMD 0x52
|
||
#define BLOCK64_ERASE_CMD 0xD8
|
||
#define BLOCK64_ERASE_CMD_4BYTE 0xDC
|
||
#define CHIP_ERASE_CMD 0xC7
|
||
|
||
#define PROG_ERASE_RESUME_CMD 0x7A
|
||
#define PROG_ERASE_SUSPEND_CMD 0x75
|
||
|
||
#define ENTER_4_BYTE_ADDR_MODE_CMD 0xB7
|
||
|
||
/* 状态寄存器标志 */
|
||
#define W25Q256JV_FSR_BUSY ((uint8_t)0x01) /*!< busy */
|
||
#define W25Q256JV_FSR_WREN ((uint8_t)0x02) /*!< write enable */
|
||
#define W25Q256JV_FSR_QE ((uint8_t)0x02) /*!< quad enable */
|
||
#define W25Q256FV_FSR_4ByteAddrMode ((uint8_t)0x01) /*!< 4字节地址模式 */
|
||
|
||
/*命令定义-结尾*******************************/
|
||
|
||
|
||
/*QSPI接口定义-开头****************************/
|
||
#define QSPI_FLASH QUADSPI
|
||
#define QSPI_FLASH_CLK_ENABLE() __QSPI_CLK_ENABLE()
|
||
|
||
#define QSPI_MDMA_CLK_ENABLE() __HAL_RCC_MDMA_CLK_ENABLE()
|
||
|
||
#define QSPI_FORCE_RESET() __HAL_RCC_QSPI_FORCE_RESET()
|
||
#define QSPI_RELEASE_RESET() __HAL_RCC_QSPI_RELEASE_RESET()
|
||
|
||
#define QSPI_FLASH_CLK_PIN GPIO_PIN_2
|
||
#define QSPI_FLASH_CLK_GPIO_PORT GPIOB
|
||
#define QSPI_FLASH_CLK_GPIO_ENABLE() __GPIOB_CLK_ENABLE()
|
||
#define QSPI_FLASH_CLK_GPIO_AF GPIO_AF9_QUADSPI
|
||
|
||
#define QSPI_FLASH_BK1_IO0_PIN GPIO_PIN_8
|
||
#define QSPI_FLASH_BK1_IO0_PORT GPIOF
|
||
#define QSPI_FLASH_BK1_IO0_CLK_ENABLE() __GPIOF_CLK_ENABLE()
|
||
#define QSPI_FLASH_BK1_IO0_AF GPIO_AF10_QUADSPI
|
||
|
||
#define QSPI_FLASH_BK1_IO1_PIN GPIO_PIN_9
|
||
#define QSPI_FLASH_BK1_IO1_PORT GPIOF
|
||
#define QSPI_FLASH_BK1_IO1_CLK_ENABLE() __GPIOF_CLK_ENABLE()
|
||
#define QSPI_FLASH_BK1_IO1_AF GPIO_AF10_QUADSPI
|
||
|
||
#define QSPI_FLASH_BK1_IO2_PIN GPIO_PIN_7
|
||
#define QSPI_FLASH_BK1_IO2_PORT GPIOF
|
||
#define QSPI_FLASH_BK1_IO2_CLK_ENABLE() __GPIOF_CLK_ENABLE()
|
||
#define QSPI_FLASH_BK1_IO2_AF GPIO_AF9_QUADSPI
|
||
|
||
#define QSPI_FLASH_BK1_IO3_PIN GPIO_PIN_6
|
||
#define QSPI_FLASH_BK1_IO3_PORT GPIOF
|
||
#define QSPI_FLASH_BK1_IO3_CLK_ENABLE() __GPIOF_CLK_ENABLE()
|
||
#define QSPI_FLASH_BK1_IO3_AF GPIO_AF9_QUADSPI
|
||
|
||
#define QSPI_FLASH_CS_PIN GPIO_PIN_6
|
||
#define QSPI_FLASH_CS_GPIO_PORT GPIOG
|
||
#define QSPI_FLASH_CS_GPIO_CLK_ENABLE() __GPIOG_CLK_ENABLE()
|
||
#define QSPI_FLASH_CS_GPIO_AF GPIO_AF10_QUADSPI
|
||
|
||
/*QSPI BANK2接口定义-开头****************************/
|
||
#define QSPI_FLASH_BK2_IO0_PIN GPIO_PIN_2
|
||
#define QSPI_FLASH_BK2_IO0_PORT GPIOH
|
||
#define QSPI_FLASH_BK2_IO0_CLK_ENABLE() __GPIOH_CLK_ENABLE()
|
||
#define QSPI_FLASH_BK2_IO0_AF GPIO_AF9_QUADSPI
|
||
|
||
#define QSPI_FLASH_BK2_IO1_PIN GPIO_PIN_3
|
||
#define QSPI_FLASH_BK2_IO1_PORT GPIOH
|
||
#define QSPI_FLASH_BK2_IO1_CLK_ENABLE() __GPIOH_CLK_ENABLE()
|
||
#define QSPI_FLASH_BK2_IO1_AF GPIO_AF9_QUADSPI
|
||
|
||
#define QSPI_FLASH_BK2_IO2_PIN GPIO_PIN_9
|
||
#define QSPI_FLASH_BK2_IO2_PORT GPIOG
|
||
#define QSPI_FLASH_BK2_IO2_CLK_ENABLE() __GPIOG_CLK_ENABLE()
|
||
#define QSPI_FLASH_BK2_IO2_AF GPIO_AF9_QUADSPI
|
||
|
||
#define QSPI_FLASH_BK2_IO3_PIN GPIO_PIN_14
|
||
#define QSPI_FLASH_BK2_IO3_PORT GPIOG
|
||
#define QSPI_FLASH_BK2_IO3_CLK_ENABLE() __GPIOG_CLK_ENABLE()
|
||
#define QSPI_FLASH_BK2_IO3_AF GPIO_AF9_QUADSPI
|
||
|
||
|
||
void QSPI_FLASH_Init(void);
|
||
uint8_t BSP_QSPI_Init(void);
|
||
uint8_t BSP_QSPI_Erase_Sector(uint32_t SectorAddress);
|
||
uint8_t BSP_QSPI_Erase_Block32(uint32_t BlockAddress);
|
||
uint8_t BSP_QSPI_Erase_Block64(uint32_t BlockAddress);
|
||
uint8_t BSP_QSPI_Erase_Chip(void);
|
||
uint8_t BSP_QSPI_FastRead(uint8_t* pData, uint32_t ReadAddr, uint32_t Size);
|
||
uint8_t BSP_QSPI_Read(uint8_t* pData, uint32_t ReadAddr, uint32_t Size);
|
||
uint8_t BSP_QSPI_Write(uint8_t* pData, uint32_t WriteAddr, uint32_t Size);
|
||
uint32_t QSPI_EnableMemoryMappedMode(void); //使能内存映射模式
|
||
|
||
static uint8_t QSPI_ResetMemory(void);
|
||
static uint8_t QSPI_WriteEnable(void);
|
||
static uint8_t QSPI_AutoPollingMemReady(uint32_t Timeout);
|
||
|
||
uint32_t QSPI_FLASH_ReadDeviceID(void);
|
||
uint32_t QSPI_FLASH_ReadID(void);
|
||
|
||
uint32_t QSPI_FLASH_ReadStatusReg(uint8_t reg);
|
||
uint32_t QSPI_FLASH_WriteStatusReg(uint8_t reg,uint8_t regvalue);
|
||
void QSPI_Set_WP_High(void);
|
||
void QSPI_Set_WP_TO_QSPI_IO(void);
|
||
|
||
#endif /* __SPI_FLASH_H */
|
||
|