/**
  ******************************************************************
  * @file    main.c
  * @author  fire
  * @version V1.0
  * @date    2018-xx-xx
  * @brief   GPIO输出--使用固件库点亮LED灯
  ******************************************************************
  * @attention
  *
  * 实验平台:野火 STM32H750开发板 
  * 论坛    :http://www.firebbs.cn
  * 淘宝    :http://firestm32.taobao.com
  *
  ******************************************************************
  */  
#include "stm32h7xx.h"
#include "main.h"
#include "./led/bsp_led.h"
#include "./delay/core_delay.h"   
/**
  * @brief  主函数
  * @param  无
  * @retval 无
  */
int main(void)
{
	/* 系统时钟初始化成480MHz */
	SystemClock_Config();
	/* LED 端口初始化 */
	LED_GPIO_Config();	
	/* 控制LED灯 */
	while (1)
	{
		LED1( ON );			 // 亮 
		HAL_Delay(1000);
		LED1( OFF );		  // 灭
		HAL_Delay(1000);

		LED2( ON );			// 亮 
		HAL_Delay(1000);
		LED2( OFF );		  // 灭

		LED3( ON );			 // 亮 
		HAL_Delay(1000);
		LED3( OFF );		  // 灭	
		
		/*轮流显示 红绿蓝黄紫青白 颜色*/
		LED_RED;
		HAL_Delay(1000);
		
		LED_GREEN;
		HAL_Delay(1000);
		
		LED_BLUE;
		HAL_Delay(1000);
		
		LED_YELLOW;
		HAL_Delay(1000);
		
		LED_PURPLE;
		HAL_Delay(1000);
						
		LED_CYAN;
		HAL_Delay(1000);
		
		LED_WHITE;
		HAL_Delay(1000);
		
		LED_RGBOFF;
		HAL_Delay(1000);
	}
}


/**
  * @brief  System Clock 配置
  *         system Clock 配置如下: 
	*            System Clock source  = PLL (HSE)
	*            SYSCLK(Hz)           = 480000000 (CPU Clock)
	*            HCLK(Hz)             = 240000000 (AXI and AHBs Clock)
	*            AHB Prescaler        = 2
	*            D1 APB3 Prescaler    = 2 (APB3 Clock  120MHz)
	*            D2 APB1 Prescaler    = 2 (APB1 Clock  120MHz)
	*            D2 APB2 Prescaler    = 2 (APB2 Clock  120MHz)
	*            D3 APB4 Prescaler    = 2 (APB4 Clock  120MHz)
	*            HSE Frequency(Hz)    = 25000000
	*            PLL_M                = 5
	*            PLL_N                = 192
	*            PLL_P                = 2
	*            PLL_Q                = 2
	*            PLL_R                = 2
	*            VDD(V)               = 3.3
	*            Flash Latency(WS)    = 4
  * @param  None
  * @retval None
  */
/**
  * @brief System Clock Configuration
  * @retval None
  */
void SystemClock_Config(void)
{
  RCC_OscInitTypeDef RCC_OscInitStruct = {0};
  RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};

  /** Supply configuration update enable 
  */
  HAL_PWREx_ConfigSupply(PWR_LDO_SUPPLY);
  /** Configure the main internal regulator output voltage 
  */
  __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE0);

  while(!__HAL_PWR_GET_FLAG(PWR_FLAG_VOSRDY)) {}
  /** Initializes the CPU, AHB and APB busses clocks 
  */
  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
  RCC_OscInitStruct.HSEState = RCC_HSE_ON;
  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
  RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
  RCC_OscInitStruct.PLL.PLLM = 5;
  RCC_OscInitStruct.PLL.PLLN = 192;
  RCC_OscInitStruct.PLL.PLLP = 2;
  RCC_OscInitStruct.PLL.PLLQ = 2;
  RCC_OscInitStruct.PLL.PLLR = 2;
  RCC_OscInitStruct.PLL.PLLRGE = RCC_PLL1VCIRANGE_2;
  RCC_OscInitStruct.PLL.PLLVCOSEL = RCC_PLL1VCOWIDE;
  RCC_OscInitStruct.PLL.PLLFRACN = 0;
  if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
  {
  }
  /** Initializes the CPU, AHB and APB busses clocks 
  */
  RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK
                              |RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2
                              |RCC_CLOCKTYPE_D3PCLK1|RCC_CLOCKTYPE_D1PCLK1;
  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
  RCC_ClkInitStruct.SYSCLKDivider = RCC_SYSCLK_DIV1;
  RCC_ClkInitStruct.AHBCLKDivider = RCC_HCLK_DIV2;
  RCC_ClkInitStruct.APB3CLKDivider = RCC_APB3_DIV2;
  RCC_ClkInitStruct.APB1CLKDivider = RCC_APB1_DIV2;
  RCC_ClkInitStruct.APB2CLKDivider = RCC_APB2_DIV2;
  RCC_ClkInitStruct.APB4CLKDivider = RCC_APB4_DIV2;

  if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_4) != HAL_OK)
  {
  }
}
/****************************END OF FILE***************************/